"An era ahead of microcement and quartz resins"
|
Intended use
CEMENTO 3D is ideal for: floors, walls, shower cubicles, bathrooms, stairs - for exteriors and interiors - environments for civil and commercial use - suitable for heated floors - swimming pools, furniture and furnishing accessories - Knowledge of the products even if our application cycle includes only one anchoring primer, it is also true that in front of some types of substrates such as screeds, parquet, wood, etc., ground-floor dwellings, substrates subject to rising damp, etc. have the optimal knowledge to be able to create a solid and effective structure that lasts over time. |
|
Preparation of Beton KA+KB
Pour about 3/3.5 liters of KB into an empty and clean bucket and pour the KA in small doses, mix with a mechanical stirrer until a homogeneous and lump-free paste is obtained. The mixture remains workable for about three hours depending on the climatic conditions. It is recommended to color Beton KA+KB in the same color as Cemento 3D. Application on screed On an existing screed floor or covering that has been cured for at least 28 days, it is advisable to make sure that there are no cracks, proceed with the spreading of BETON KA+KB using a 3mm stainless steel trowel and with the product still fresh lay over the mesh in glass fiber of 70/80 gr/m² and immediately smooth the treated surface with the smooth side of the trowel in order to level the product and drown the net inside the still fresh mixture and make the surface uniform, continue with the same procedure for the whole surface. Application on tiles On a floor or wall with old tiles it is advisable to make sure that they are well anchored and free from oils and greases, proceed with the spreading of BETON KA+KB using a 3mm stainless steel trowel and with the product still fresh smooth the surface treated with the smooth side of the trowel in order to level the product, continue with the same procedure for the entire surface. |
|
Application on tiles with traces and restorations
On a floor or wall with old tiles where there are previously restored traces and cracks for the passage of water pipes, for heating, etc., proceed with the laying of a 70/80 gr/m² fiberglass mesh over the entire surface to be treat, apply a single layer of Beton Ka+KB on the mesh using a stainless steel trowel.
It is recommended to add 4.5 liters of KB to Beton KA so that it penetrates inside the network and anchors itself on the existing tile, continuing with the same procedure for the entire surface.
On a floor or wall with old tiles where there are previously restored traces and cracks for the passage of water pipes, for heating, etc., proceed with the laying of a 70/80 gr/m² fiberglass mesh over the entire surface to be treat, apply a single layer of Beton Ka+KB on the mesh using a stainless steel trowel.
It is recommended to add 4.5 liters of KB to Beton KA so that it penetrates inside the network and anchors itself on the existing tile, continuing with the same procedure for the entire surface.
|
Product
CEMENTO 3D is a new generation structured nanocement, premixed in powder form composed of selected quartz sands and marble powders, minerals and special additives. CEMENTO 3D is the ideal solution for those who do not like joints because it allows the creation of continuous surfaces, internal and external, without joints that last over time. The complete CEMENTO 3D cycle described here is certified. Blend, colors and perfect application it is always assumed that the pigments, coloring pastes or toners used to color the products are the same. Behind each color proposed by the manufacturer there are various studies and very strict laboratory tests and it is precisely for this reason that it is necessary to know first of all the mixing of the dyes and that of the product itself. Preparation of the Cemento 3D CEMENTO 3D is mixed with drinking water (1 kg of CEMENTO 3D + 300 ml of water) using a mechanical stirrer until a homogeneous and lump-free paste is obtained. |
The mixture remains workable for about six hours depending on the climatic conditions.
We recommend the preparation of CEMENTO 3D as follows:
• First layer of CEMENTO 3D, mix 20 kg of powder in 6 liters of drinking water
• Second and last layer of CEMENTO 3D, mix 20 kg of powder in 6 liters of drinking water
We recommend the preparation of CEMENTO 3D as follows:
• First layer of CEMENTO 3D, mix 20 kg of powder in 6 liters of drinking water
• Second and last layer of CEMENTO 3D, mix 20 kg of powder in 6 liters of drinking water
|
Application method of 3D Cement
After having mixed and colored the CEMENTO 3D, apply a first layer using a 3 mm stainless steel trowel and immediately smooth the treated surface, once it has dried after 12 hours proceed with the second coat of CEMENTO 3D using a stainless-steel trowel and let it dry for at least 6/8 hours, proceed with the third and last coat as before. Allow the surface to dry for at least 24 hours and proceed with the transparent semi-gloss and/or opaque finish of Decor Finish (it is advisable to consult the construction book for the correct installation of all the steps). Taking some precautions before and during the application of CEMENTO 3D is of considerable importance, for example, shoes must be protected with special protections, do not drag the bucket or smoke during installation, if these simple precautions are not observed there is a risk of compromise the result of the work. |
|
|
Transparent finish
Decor Finish is a water-based nanostructured transparent polyacrylic paint, one-component of the latest generation, semi-gloss, opaque and non-slip, waterproof and suitable for both indoor and outdoor use. Perfect success of the works one of the main factors for the success of a floor is not to be superficial in the evaluation of the laying surfaces that compromise the success of a continuous surface, the drafting, application times and cleaning of the environment is essential for the perfect success of a 3D concrete floor or wall covering. Preparation of the Decor Finish Decor Finish is ready to use, do not add water or dyes. After shaking the product well, pour it into a clean bucket, the coverage of Decor Finish is approximately 10 m² in three layers. The application must be done following crossed movements and no excess product should be left, so we will obtain a compact and uniform surface (the first layer of Decor Finish has a primary role for the perfect success of the work and for water permeability) . After 12 hours and before starting the application of the second layer of Decor Finish it is advisable to check that there are no lumps or impurities on the surface, in this case proceed with cleaning using a vacuum cleaner. (it is essential that the surface is perfectly clean before proceeding with the second layer), spread |
a second layer of Decor Finish evenly over the entire surface, taking care to distribute the product well and go over it several times and not to leave excess product.
After 12 hours from the second layer of Decor Finish and before starting the application of the third layer it is important to respect all the steps that have been made for the second layer. The drying times for each layer are significantly influenced by the temperature and ventilation during drying and may make it necessary to extend the drying times themselves. In case of insufficient respect of the drying times, the applied product could wrinkle, crack, form strips or lift from the support.
After 12 hours from the second layer of Decor Finish and before starting the application of the third layer it is important to respect all the steps that have been made for the second layer. The drying times for each layer are significantly influenced by the temperature and ventilation during drying and may make it necessary to extend the drying times themselves. In case of insufficient respect of the drying times, the applied product could wrinkle, crack, form strips or lift from the support.
|
Important note:
We do not recommend applying opaque Decor Finish directly on CEMENTO 3D in natural white or light shades. The opaque version of Decor Finish contains a straw-colored opacifying paste and would alter the natural white of the surface, creating unsightly yellowish halos. What to do? Apply a layer of Decor Finish Semigloss and proceed with two more coats of Decor Finish opaque. The information contained herein is the result of our best knowledge and, as such, is disclosed for information purposes, therefore it does not undertake the responsibility of our Company towards any disputes arising from conditions of use that are beyond our control, for any clarification we recommend before carrying out the work, contact our technical support. New packaging, new formula this is the new look of CEMENTO 3D |
|
ATTACHED DOCUMENTATION
|
| ||||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| sds_technical_data_epoxyfloor.pdf |
N.B. The company assumes no responsibility for the correct use and installation of Cemento 3D floors and walls by people who have not completed a Master of Technical Theoretical Professional Training at our Academy
For over fifteen years the commitment has been based on the research and development of new production systems
so as to bring increasingly innovative products to the global market in order to reduce CO2 emissions,
because for us the environment is at the center of our every choice.
so as to bring increasingly innovative products to the global market in order to reduce CO2 emissions,
because for us the environment is at the center of our every choice.
THREE PRODUCTS FOR A CERTIFIED CONTINUOUS SURFACE
Beton KA+KBBorn to join on Any support |
Cemento 3DA new concept called NANOCEMENTO |
Decor Finishstudied and designed to last over time! |
CONTINUOUS ECO-COMPATIBLE SURFACES FOR FLOORS
COVERINGS AND FURNIture
impact resistant
|
heat resistant
|
Resistant to chemical agents
|
Designed for low temperatures
|
Permeable to water
|
Electrostatic surface
|
Ideal for heated floors
|
FOR A GREAT RESULT YOU MUST TRAVEL THE RIGHT ROAD!
Non-slip finishes
|
UV resistant
|
Resistant to traction and compression
|
Weatherproof
|
Excellent flexibility
|
Abrasion resistant
|
Reduced application cycles
|
14 good reasons to choose a Cemento3D floor
The complete cycle of floors and walls is certified by the Tecnocprove laboratory of Ostuni ITaly
The complete cycle of floors and walls is certified by the Tecnocprove laboratory of Ostuni ITaly
